20% OFF SELECTED BRANDS! EDUARD, KINETIC, SPECIAL HOBBY, CMK & more
1:48 EA-18G Growler CANOPY INNER SIDE kabuki masks for Meng

1:48 EA-18G Growler CANOPY INNER SIDE kabuki masks for Meng

3.96 €
Add to Cart

1:48 EA-18G Growler CANOPY INNER SIDE kabuki masks for Meng

EA-18G Growler canopy inner side masks, 1:48 are pre-cut New Ware kabuki masks for the Meng kit. This is not an aircraft model but a masking accessory that makes painting the glazing framing easier as seen from inside.

Scale1:48
Manufacturer New Ware
Product EAN8591111248648

Responsibility details are not available.

3.96 €
3.27 € without VAT
1 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

EA-18G Growler canopy inner side masks, 1:48 (New Ware)

A set of pre-cut kabuki masks for a 1:48 model of the EA-18G Growler from the manufacturer Meng. It concentrates on one particular part of the build, the inner side of the cockpit canopy. The framing of the glazing is seen from the pilot station in the interior color, and outer masks alone are not enough for that detail. This is not an aircraft kit but an accessory to one, so you have to own the model itself.

The real subject

The EA-18G Growler is a carrier-borne electronic warfare aircraft of the US Navy. It is based on the two-seat F/A-18F Super Hornet, with which it shares the airframe and the powerplant, and it carries equipment for jamming and suppressing air defenses. One way to tell it from the Super Hornet is the pods on the wingtips. It entered squadron service in the late 2000s and replaced the older EA-6B Prowler.

Use and tips

The masks are die-cut on a carrier film. Lift the individual parts carefully with the tip of a scalpel or with tweezers, lay them on a clean, degreased surface and press the edges down with a toothpick or a wooden stick. Do not touch the glazing with your fingers before masking. Apply the paint in thin coats and at lower pressure so that it does not run under the edge of the mask. On the inner framing it helps to spray the area with the interior color first and only then carry on. Lift the mask off shortly after it has dried, while the layer is still flexible, and the edge will stay sharp.

Who the set is for

  • Builders of the 1:48 EA-18G Growler model from the manufacturer Meng
  • Modelers bothered by unfinished cockpit framing seen from inside
  • Those who want to save the time of cutting masking tape by hand
  • An accessory alongside the basic masks for the outer glazing

This is a masking accessory, not a kit. The aircraft model, the paints and the glue are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. This is a set of masking parts for building and painting a model. The EA-18G Growler kit itself has to be bought separately.

It is cut for the 1:48 EA-18G Growler model from the manufacturer Meng. On other kits of the same aircraft the shape of the glazing may not match.

The canopy frames are seen from the pilot station in the interior color. Painted only from outside, the cockpit looks unfinished up close.

Shortly after the paint has dried, while the layer is still flexible. On fully cured paint the edge chips more easily.

Last seen

New WareNWAM09931:48

1:48 EA-18G Growler CANOPY INNER SIDE kabuki masks for Meng

EA-18G Growler canopy inner side masks, 1:48 are pre-cut New Ware kabuki masks for the Meng kit. This is not an aircraft model but a masking accessory that makes painting the glazing framing easier as seen from inside.
In stock
3.96 €
Offset Scale ModelsOFFS480331:48

1:48 Roof Tiles 3D printed - 100 + 22 pcs

The diorama accessory 1:48 Roof Tiles 3D printed - 100 + 22 pcs from Offset Scale Models brings roof tiles made by 3D printing, according to the name in counts of 100 and 22 pieces.
In stock
9.16 €
Ice Yellow
-20 %
Favorite
AMMO of Mig JimenezA.MIG-0640

Ice Yellow

Ice Yellow is a paint from the AMMO of Mig Jimenez range intended for the dry brush technique. The product name carries only the name of the shade.
In stock
3.96 €3.17 € You save 0.79 €
Mettalic DetailsMDP320341:32

1:32 USSR WWII Aircrew Parachutes

Printed parachutes of Soviet aircrews of the Second World War, worked out for 1:32 scale.
In stock
3.16 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.