1:32 A-6E Intruder 3D-Printed & coloured Interior on decal paper (Trumpeter) (Small version)

1:32 A-6E Intruder 3D-Printed & coloured Interior on decal paper (Trumpeter) (Small version)

32.36 €
Add to Cart

1:32 A-6E Intruder 3D-Printed & coloured Interior on decal paper (Trumpeter) (Small version)

Colored interior decals for a model of the A-6E Intruder in 1:32 scale, the small version of the set. They are applied over a gloss base and replace the flat kit parts. Target kit: Trumpeter.

Scale1:32
Manufacturer Quinta Studio
Product EAN8591111427098

Responsibility details are not available.

43.16 € 32.36 €
26.74 € without VAT
−25 % You save 10.80 €
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

A-6E Intruder – interior decals 1:32, small version

This is a colored decal set for the interior of a model of the A-6E Intruder in 1:32 scale in the small version. The small version designation comes straight from the name of the product and distinguishes it from the full set on the same subject. It is not a model or a kit but an accessory applied to finished painted parts. The decals are shaped for the parts of the Trumpeter kit.

The real subject

The A-6 Intruder was a twin-engine carrier attack aircraft intended for all-weather operations, with a crew of two sitting side by side. The E version was the most common operational form. The wide cockpit means that detail under an open canopy comes into its own.

How the set is applied

The base must be smooth and glossy. So overcoat the painted part with gloss varnish and let it cure completely. Then release the decal after about fifteen seconds in lukewarm water, place it, align it and blot up the excess water with a soft cloth. Do not use a decal softener or setting solution; their chemicals would damage the printed resin and ruin the element. Do not handle the part until it has dried. Seal the finished interior with varnish in the matching degree of sheen.

What the set does on the model

The set replaces the flat kit parts with a colored print that gives a three-dimensional impression. It saves painting the smallest details and unifies the look of the whole interior. Degrease the plastic surface before application and level any coarse relief.

Who the set is for

  • For builders of the Intruder in 1:32 scale for whom a smaller extent of the set is enough
  • For modelers who build a model with the canopy closed
  • For those who want a colored interior without painting tiny areas
  • As an accessory for a kit, not as a model in its own right

The set is an accessory for a kit, not a model in its own right. Paints, glue and varnishes are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is the smaller variant alongside the full set on the same subject.

A plastic kit, paints for the base and gloss varnish. Do not get a softener or setting solution, as they must not be used with this line. The set itself is only an accessory.

Matte paint is microscopically broken up, air remains under the decal and its edge begins to show through with a silvery look.

Briefly, yes, while there is water under it. Once it starts to dry on, do not move it any more, otherwise it will be damaged.

It is intended for the Trumpeter kit.

Last seen

1:32 A-6E Intruder 3D-Printed & coloured Interior on decal paper (Trumpeter) (Small version)-25 %Stock ClearanceFavorite
Quinta StudioQDS321061:32

1:32 A-6E Intruder 3D-Printed & coloured Interior on decal paper (Trumpeter) (Small version)

Colored interior decals for a model of the A-6E Intruder in 1:32 scale, the small version of the set. They are applied over a gloss base and replace the flat kit parts. Target kit: Trumpeter.
5 leftof 6
43.16 €32.36 € You save 10.80 €
RC-21171:72

1:72 remote control tank Tiger

In stock
19.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.