20% OFF SELECTED BRANDS! EDUARD, KINETIC, SPECIAL HOBBY, CMK & more
1:48 P-47D-25RE Thunderbolt one-sided express fit mask for MINIART

1:48 P-47D-25RE Thunderbolt one-sided express fit mask for MINIART

5.41 €
Add to Cart

1:48 P-47D-25RE Thunderbolt one-sided express fit mask for MINIART

A single-sided express fit masking set in 1:48 scale for a model of the Republic P-47D-25RE Thunderbolt fighter-bomber from the MiniArt kit. The pre-cut masks speed up covering the glazing and help toward a sharp paint edge on the canopy frames.

Scale1:48
Manufacturer Art Scale
Product EAN8591111482721

Responsibility details are not available.

6.76 € 5.41 €
4.47 € without VAT
−20 % You save 1.35 €
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Masking set 1:48 P-47D-25RE Thunderbolt, single-sided

This is a set of pre-cut masking parts for modelers, not a kit of the airplane. The masks are shaped to fit the MiniArt Thunderbolt kit in 1:48 scale and are applied to the canopy glazing and to the surfaces that are to stay clear after spraying. The marking one-sided, that is, single-sided, means that the set covers the outer side of the glazing; the inner side is masked by hand, or with a closed canopy is not dealt with at all. Anyone who wants a correctly framed cockpit even seen from the inside reaches for the double-sided variant of the same set.

The real subject

The Republic P-47 Thunderbolt was one of the heaviest single-engine fighters of the Second World War. It was powered by a Pratt and Whitney R-2800 Double Wasp radial engine with a turbocharger, thanks to which the aircraft held its performance even at great altitudes. The P-47D-25 production block brought a cut-down fuselage spine and a bubble canopy, which fundamentally improved the pilot's view to the rear; the older blocks had a framed canopy and a full spine. The RE suffix refers to the parent plant at Farmingdale. Thunderbolts served as escort fighters for bomber formations and were famous above all as fighter-bombers against ground targets, where a rugged structure and heavy armament helped them.

Use and tips

Degrease the glazing before applying the masks and handle them with soft-jawed tweezers. Press an applied mask down along the whole edge of the frame with a toothpick or a wooden skewer so that paint does not run under the rim. With a bubble canopy it pays to spray several thin coats rather than one heavy one, otherwise a visible step stays at the edge of the mask. Remove the mask while the paint is only dry and not cured for several days, and peel it slowly back over itself, not straight upward.

Who the set is for

  • Modelers who are building the Thunderbolt in 1:48 scale
  • Those who want sharp canopy frames without cutting tape by hand
  • Beginners for whom masking the glazing takes up the most time
  • Collectors of American fighters of the Second World War

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. This is a masking set, that is, an accessory for a model. The Thunderbolt kit itself has to be bought separately.

The set contains masks for the outer side of the glazing. The double-sided variant of the same set additionally covers the inner side, so that the frames look right even seen into the cockpit.

Apply them to clean, degreased glazing before spraying the base coat and take them off only after the whole paint job is finished, while the paint is not yet cured.

With the usual procedure, yes. Peel them slowly, at an acute angle back over themselves, not straight away from the surface.

Last seen

1:48 P-47D-25RE Thunderbolt one-sided express fit mask for MINIART
-20 %
Favorite
Art ScaleASKM481841:48

1:48 P-47D-25RE Thunderbolt one-sided express fit mask for MINIART

A single-sided express fit masking set in 1:48 scale for a model of the Republic P-47D-25RE Thunderbolt fighter-bomber from the MiniArt kit. The pre-cut masks speed up covering the glazing and help toward a sharp paint edge on the canopy frames.
In stock
6.76 €5.41 € You save 1.35 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.