LAST CHANCE! 20% OFF Ends Tonight!
1:32 A-1H Skyraider 3D-Printed and coloured Interior on decal paper

1:32 A-1H Skyraider 3D-Printed and coloured Interior on decal paper

26.76 €
Add to Cart

1:32 A-1H Skyraider 3D-Printed and coloured Interior on decal paper

A Quinta color cockpit interior for an A-1H Skyraider model in 1:32 scale. The parts are dipped briefly in lukewarm water like a decal, and no decal softener is used on them.

Scale1:32
Manufacturer Quinta Studio
Product EAN8591111000000

Responsibility details are not available.

26.76 €
22.12 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

The real subject

The Douglas A-1H Skyraider is an American single-seat carrier-borne ground-attack aircraft with a piston radial engine. It appeared at the end of the Second World War, but it made its reputation later: it could stay over the battlefield for hours and carry a load of armament under its wings that the jets of the day could not manage. That is precisely why it was still serving in the 1960s, among other things protecting downed airmen.

What the set contains

A color cockpit interior for a model in 1:32 scale from Quinta. The parts are printed, have raised relief and are seated directly on the parts of the kit. They are applied like a decal: the part is dipped briefly in lukewarm water and slid off the backing paper into place, and no decal softener is used on them. They have no adhesive layer of their own and hold on a gloss coat. The extent of the set and the position of the individual parts are given in the manufacturer's instructions.

Building tips

Go over the surfaces the parts will sit on with a gloss coat such as Future, Klear or Tamiya X-22, as a part will not hold on matte paint. Separate the part with the point of a scalpel and, once dipped, carry it with tweezers rather than with your fingers. Lay it down by one edge first, guide it into place and only then press it with a cotton bud from the center outward so that no air is left under it; on intricate places a drop of cyanoacrylate glue helps. Finish the interior before you close the fuselage up, as you will not reach the cockpit later. If the set includes an instrument panel, a drop of clear coat run into the individual dials once they are dry will visually deepen them.

  • a color cockpit interior in 1:32 scale, from Quinta
  • printed parts with raised relief
  • applied by dipping in lukewarm water, with no decal softener
  • once dipped, the part slides off the backing paper
  • the extent of the set and the position of the parts are given in the manufacturer's instructions

Terms of supply

The aircraft kit, paints and glue are not part of the delivery, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

Yes. The cut-out part is dipped in lukewarm water for about fifteen seconds and slid off the backing paper into place. No decal softener is used.

Color cockpit interior parts in 1:32 scale. Their extent and position are given in the manufacturer's instructions. The aircraft kit is not included.

Go over the surface with a gloss coat, carry the dipped part with tweezers, lay it down by one edge and press it with a cotton bud from the center outward.

Before the fuselage is closed up. Once the fuselage halves are glued together you will no longer reach the cockpit.

Last seen

Quinta StudioQD320651:32

1:32 A-1H Skyraider 3D-Printed and coloured Interior on decal paper

A Quinta color cockpit interior for an A-1H Skyraider model in 1:32 scale. The parts are dipped briefly in lukewarm water like a decal, and no decal softener is used on them.
In stock
26.76 €
MiniartMA240091:24

1:24 FUEL & OIL DRUMS 1930-50’S SET 1. GERMAN TYPE

A set of fuel and oil drums of the German type from the years 1930 to 1950 in 1:24 scale. An accessory for models of equipment and a rewarding filler for a workshop or storeroom diorama.
In stock
11.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.