29.–30. 10. z technických důvodů zavřeno. / Closed 29–30 October for technical reasons.

1:48 A-1H wheels

Eduard 1:48 A-1H wheels is a resin set of wheels for a model of the Douglas A-1H Skyraider in 1:48 scale. It is not a kit but a replacement part for raising the level of detail on the landing gear.

Scale1:48
Manufacturer Eduard
Product EAN8991111049784

Responsibility details are not available.

6.80 € 5.12 €
4.23 € without VAT
−25 % You save 1.68 €
1 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Eduard 1:48 A-1H wheels — resin wheels for the Skyraider

A set of wheels in resin from the Czech manufacturer Eduard, intended for a model of the Douglas A-1H Skyraider in 1:48 scale. It is not a kit nor a model of the aircraft but a replacement part, with which the landing gear wheels in the basic kit are swapped out. Eduard makes several accessories for the same aircraft under very similar names, and the individual ranges are recognized by the exact designation of the set; this one belongs to the resin range.

What the set is for

Wheels in injection-molded plastic tend to be split into two halves with the seam running across the tread, that is across the most visible place on the whole part. A resin casting is in one piece, has a more sharply drawn pattern and a more cleanly made hub. The parts are cut off the casting block with a saw or a sharp cutter, the mating face is leveled, and before gluing the castings are washed in warm water with detergent, so that no release agent from the mold stays on them. They are glued with cyanoacrylate glue, as ordinary cement for plastic does not dissolve resin and the joint would not hold.

Pre-painted parts and painting

Wheels from this range are supplied in the color of the casting and nothing on them is pre-painted — allow for spraying them completely. The proven procedure is to paint the tire and the hub separately: first the whole part in the dark shade of the tire, then the tread and the sidewalls are masked and only the hub is oversprayed. The tire is to stay matte, whereas the hub follows the surrounding finish of the aircraft in shade and sheen, so that it does not look like a foreign piece in the wheel well. The wheels are fitted to the model only at the very end, after the airframe has been sprayed and varnished, because they are easily soiled or damaged under masking tape and during handling.

Who the set is for

  • Builders of the Skyraider in 1:48 scale who are bothered by the seam across the tread
  • Modelers who want to bring the landing gear out without rebuilding the whole kit
  • Those who already have experience of gluing resin with cyanoacrylate glue

It is an accessory, not a kit. The basic model, glue and paints are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. They are replacement landing gear wheels, which will replace the plastic parts in your Skyraider kit in 1:48 scale. The model itself has to be obtained separately.

With cyanoacrylate glue. Ordinary cement for plastic does not dissolve resin, so the joint would not hold. Wash the parts in warm water with detergent before gluing.

No, they are supplied in the color of the casting. The recommended procedure is to spray the whole part in the dark shade of the tire, then mask the tread and overspray the hub.

Best only after the airframe has been sprayed and varnished. Fitted wheels are easily damaged or soiled during masking and handling.

Last seen

1:48 A-1H wheels-25 %Stock ClearanceFavorite
EduardED6487601:48

1:48 A-1H wheels

Eduard 1:48 A-1H wheels is a resin set of wheels for a model of the Douglas A-1H Skyraider in 1:48 scale. It is not a kit but a replacement part for raising the level of detail on the landing gear.
Last one!of 5
6.80 €5.12 € You save 1.68 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.