29.–30. 10. z technických důvodů zavřeno. / Closed 29–30 October for technical reasons.

1:48 F.M.A. IA-58A Pucara canopy paint Masks

1:48 F.M.A. IA-58A Pucara canopy paint Masks is a set of painting masks for the cockpit glazing, not a kit. It makes it possible to spray the frames of the canopy cleanly on a model in 1:48 scale.

Scale1:48
Manufacturer Mettalic Details
Product EAN8591111713610

Responsibility details are not available.

3.96 €
3.27 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

F.M.A. IA-58A Pucara canopy masking set 1:48 from Metallic Details

This item is an accessory for the build, not a model of the airplane. The set contains painting masks cut to the shape of the cockpit glazing; they are stuck on the clear part, oversprayed with the color of the frames and taken off once the paint has dried. The Pucara has a long two-seat canopy with a prominent windscreen and several dividing frames, so masking is one of the visible operations of the whole build. The set is made by Metallic Details.

The real subject

The F.M.A. IA-58 Pucara is an Argentine twin-engined turboprop ground-attack aircraft intended for supporting ground forces, for reconnaissance and for counterinsurgency. In design it is a low-wing monoplane with two turboprop engines on the wing, retractable nose gear and a crew sitting in tandem under common glazing. The IA-58A version is the basic production standard. The machine was designed for operating from short and unprepared strips, which matches the robust landing gear and the high-set cockpit with a wide view forward and downward.

How to use the masks

Wash and degrease the clear part, so that the mask holds reliably. Take the masks out of the sheet with the tip of a sharp knife and transfer them with tweezers straight onto the areas that are to stay transparent. Press the edges down along the whole perimeter, and on the convex parts of the canopy work from the center toward the edges and form the curvature with a toothpick. Cut any uncovered sections from the waste material of the sheet or complete them with narrow masking tape. Overspray the frames first with the interior shade, then with the exterior finish, always in several thin coats. Take the masks off shortly after the paint has dried, slowly and at a sharp angle.

Who the set is for

  • Modelers building the IA-58A Pucara in 1:48 scale.
  • Those interested in South American aviation machines.
  • Those who want sharp frames without cutting tape by hand.
  • Builders for whom the long tandem canopy is the main visual element.

The set contains only masking parts. The model, paints and glue are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. These are purely painting masks for the clear parts of the cockpit, and the kit has to be obtained separately.

It is the basic production standard of the Argentine Pucara ground-attack aircraft. The set is described for this version.

Press it down from the center toward the edges and form the curvature with a wooden toothpick. Where everything cannot be covered, complete it with narrow masking tape.

Shortly after the paint has dried, slowly and at a sharp angle. Removing it later may tear the edge of the finish away.

Last seen

Mettalic DetailsMDM48121:48

1:48 F.M.A. IA-58A Pucara canopy paint Masks

1:48 F.M.A. IA-58A Pucara canopy paint Masks is a set of painting masks for the cockpit glazing, not a kit. It makes it possible to spray the frames of the canopy cleanly on a model in 1:48 scale.
In stock
3.96 €
AoshimaAO054821:24

1:24 Nissan UF31 Leopard 3.0 Ultima '86

The Aoshima 1:24 plastic kit of the Nissan Leopard 3.0 Ultima (UF31) of 1986 captures the luxury personal coupe of the F31 generation in the top trim with a V6 engine.
In stock
23.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.