1:32 Cessna L-19/O-1 Bird Dog (outside-inside)

The 1:32 Cessna L-19/O-1 Bird Dog masking set (outside and inside) from Montex is an accessory for a plastic kit you already own, not a model. It deals with spraying the frames of the extensive cockpit glazing from outside and from inside.

Scale1:32
Manufacturer Montex
Product EAN8591111000000

Responsibility details are not available.

6.76 €
5.59 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

The Montex 1:32 Cessna L-19/O-1 Bird Dog masking set

Self-adhesive masking templates for spraying the framing of the glazing in 1:32 scale. This is an accessory for a kit, which has to be obtained separately, not a model. On an observation aircraft with glazing at the sides and above the pilot's head, the frames make up a large part of the visible area of the fuselage, so the overall impression of the finished model stands or falls on how they are done.

The real subject

The Cessna L-19, later designated O-1 Bird Dog, was an American high-wing monoplane with fixed landing gear, derived from a civil design and used for observation, liaison and the control of air support. It is distinguished by glazing carried into the side doors and into the roof of the cabin, which gave the crew a view in practically every direction. It served with a number of armed forces and, after the end of its military career, in civil use.

How to work with the masks

First work out which masks belong on the roof and which in the side panes, and apply them before the fuselage is closed up, if the construction of the model allows it. Apply the inside masks first and spray the interior shade, as otherwise the frames would be very hard to finish from inside. Once the finish is done, take the masks off at a sharp angle and slowly, so that the edge of the paint separates cleanly. Remove any adhesive residue with a cotton swab moistened in clean water.

Who the set is for

  • builders of observation and liaison aircraft in 1:32 scale
  • modelers who want to manage extensive glazing without touching up by hand
  • those who mask the inside of the glazing too
  • anyone building a model with an open cockpit or open doors

The set is an accessory for a plastic kit. The kit, paints and glue are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. The package holds masking templates only; the kit has to be bought separately.

Apply the inside masks and spray the interior shade first, then apply the outside masks and lay on the outer camouflage. The masks are taken off at the very end.

Pull slowly and at a sharp angle, back over itself. Tearing it straight up quickly can pull the edge of the finish away.

Last seen

MontexMXSM321741:32

1:32 Cessna L-19/O-1 Bird Dog (outside-inside)

The 1:32 Cessna L-19/O-1 Bird Dog masking set (outside and inside) from Montex is an accessory for a plastic kit you already own, not a model. It deals with spraying the frames of the extensive cockpit glazing from outside and from inside.
In stock
6.76 €
New WareNWAM06691:72

1:72 F-4 B/C/D/E/EJ/G/J Phantom II ADVANCED kabuki masks

F-4 Phantom II ADVANCED masks (1:72) is a set of New Ware kabuki painting masks for exact masking of the glazing and other parts of a model.
In stock
6.76 €
AberABR35D0091:35

1:35 Telegraph - pillar set for 1 cross bars with 8 insulators each

An Aber telegraph pillar with 1 crossarm of 8 insulators in 1:35 scale is a diorama structure made of photo-etched parts. You build a pillar with one crossarm, not a vehicle model.
In stock
9.40 €
EduardED6723481:72

1:72 Messerschmitt Bf-109G-5/G-6 wheels 3D-Printed

Eduard 1:72 Bf 109G-5/G-6 - 3D-printed wheels replace the landing gear wheels of a model of the Bf 109G-5 or G-6 fighter.
In stock
6 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.