1:35 M2, M2A2, M3 Bradley - Tamiya

The Quickwheel masking set for the road wheels of the M2, M2A2 and M3 Bradley vehicles in 1:35 scale is cut for the Tamiya kits.

Scale1:35
Manufacturer Quickwheel
Product EAN8591111000000

Responsibility details are not available.

7.56 €
6.25 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Quickwheel M2 / M2A2 / M3 Bradley wheel masks 1:35

A masking set for painting the road wheels of the American Bradley family of fighting vehicles in the M2, M2A2 and reconnaissance M3 versions. This is not a model or a set of replacement parts: the masks cover the rim of the wheel so the rubber tire band can be sprayed on its own with a sharp edge. The set is cut for the kits from Tamiya.

What makes the running gear of the Bradley special

The Bradley has six road wheels with a rubber tire band per side, the drive sprocket at the front, the idler wheel at the rear and return rollers. Another feature is the key one, though: the whole running gear is covered by side armor skirts, which on the later versions reach down a long way. Only the lower sliver of the wheels, and the part between the skirt and the track, is left visible on a finished model. That leads plenty of modelers into the temptation to skimp on the wheels — except that it is precisely that narrow visible part that sits at the viewer's eye level, and a botched tire band positively shines there. On vehicles with an aluminum hull and a low silhouette the running gear is also captured close up in photographs almost every time. A masking set deals with this detail quickly, so it is worth spending the time on even with a covered running gear.

When the wheels come up in the build

Here the placing of the step is entirely unambiguous: the wheels have to be finished before the side skirts go on the model. Once the skirts are seated you cannot reach the wheels with an airbrush or with a finger. The routine is therefore the base coat on the hull and the wheels, a day to cure, the masks and the spraying of the tire bands, fitting the wheels to the arms — and only then the skirts, and the tracks at the very end. Anyone who glues the skirts on while building the hull, because that is the order in the instructions, ends up finishing the tire bands with a brush, blind, through a gap a few millimeters wide.

Who the set is for

  • Builders of the M2, M2A2 or M3 Bradley vehicles in 1:35 scale
  • Modelers of modern American tracked equipment
  • Those who want the running gear finished before the side skirts are glued on
  • Anyone who photographs a model close up and from ground level

This is a masking accessory, not a kit. The model, paints and glue are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

Yes. The lower sliver of the wheel stays visible at the viewer's eye level and a botched tire band is conspicuous there.

The name gives the M2, M2A2 and M3, which have their road wheels laid out identically.

Once the base shade has cured, and certainly before you glue the side skirts to the hull.

No. You use the plastic wheels from the kit; the set serves only for masking while painting.

Last seen

QuickwheelQW-1361:35

1:35 M2, M2A2, M3 Bradley - Tamiya

The Quickwheel masking set for the road wheels of the M2, M2A2 and M3 Bradley vehicles in 1:35 scale is cut for the Tamiya kits.
In stock
7.56 €
EvergreenEVG118

Profil 0,38 x 4,8 mm

A thin wide strip 0.38 x 4.8 mm in white styrene. It makes sheet metal bands, deck planks and banding on hulls. It is scored with a knife and separated by snapping.
In stock
0.32 €
EduardED323661:32

1:32 F4U-1A exteriér

The Eduard 1:32 photo-etched exterior set for the F4U-1A Corsair is a metal detail accessory for refining the surface of a model, not a stand-alone kit.
In stock
18.20 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.