1:144 H.S. Harrier GR.7/GR.9/AV-8B wheels w/ weighted tyres

1:144 H.S. Harrier GR.7/GR.9/AV-8B wheels w/ weighted tyres

4.76 €
Add to Cart

1:144 H.S. Harrier GR.7/GR.9/AV-8B wheels w/ weighted tyres

Armory 1:144 wheels for the Harrier GR.7/GR.9/AV-8B with sagging tires are a resin replacement for the wheels of the second generation Harrier. A cast contact patch gives the model a faithful stance on the surface under load.

Scale1:144
Manufacturer Armory
Product EAN8591111696425

Responsibility details are not available.

4.76 €
3.93 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Wheels for the Harrier GR.7/GR.9/AV-8B in 1:144

This add-on set from Armory is made for models of the second generation Harrier in 1:144, that is for the GR.7, GR.9 and AV-8B versions. The resin castings carry a sharper tread and sidewall pattern than small injection-molded parts usually manage, and the tires have sag cast in where they touch the runway. Once finished, the model no longer looks as though it hovers above the surface. The set is an add-on to a kit, not a model of the aircraft.

The real subject

The second generation Harrier built on the original British type with a redesigned wing and extensive changes to the airframe and the equipment. The AV-8B, GR.7 and GR.9 versions served in ground support and strike duties while keeping the ability to take off vertically and from a short run. The landing gear layout with main wheels on the fuselage centerline and outrigger wheels at the wingtips remained characteristic of the type and is clearly apparent on a model.

Usage and painting tips

Work with tweezers over a light surface, as the parts are small. Cut the casting block off with a fine saw and level the cut with sandpaper. Verify the contact patch against a flat board and watch while gluing that the model settles onto the main and the outrigger wheels at the same time. Wash the parts in warm water with dish soap before painting and let them dry out completely. They are glued with cyanoacrylate glue; cement for plastic does not work here. Paint the tire dark gray and flatten it down, then finish the hub with a brush around the rim. Hint at service dust sparingly with pigment so that a small part does not disappear under a layer of effect. Protect your airways when sanding resin, and sand wet if you can.

Who the set is for

  • Builders of second generation Harrier models in 1:144
  • Modelers bothered by the unloaded wheels from the box
  • Collectors of modern combat aircraft
  • Those who want to raise the level of detail without converting the model

This is an add-on to a plastic kit, not a model in its own right. The set is supplied unpainted; glue, paints and the base kit are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

For the second generation Harrier, that is the GR.7, GR.9 and AV-8B. For the first generation the manufacturer has a separate set.

It is a set of wheels. The gear legs and the bay doors stay as they come from the base kit.

Check the contact patches against a flat board and let the glue set only once the model settles onto the main and the outrigger wheels at the same time.

Yes. The remains of mold release agent worsen paint adhesion. Warm water with dish soap, a rinse and thorough drying is enough.

Last seen

ArmoryARAW144081:144

1:144 H.S. Harrier GR.7/GR.9/AV-8B wheels w/ weighted tyres

Armory 1:144 wheels for the Harrier GR.7/GR.9/AV-8B with sagging tires are a resin replacement for the wheels of the second generation Harrier. A cast contact patch gives the model a faithful stance on the surface under load.
In stock
4.76 €
Dead DesignNM721011:72

1:72 F-8E/J/P Crusader - Canopy Mask for Academy

Self-adhesive glazing masks for the F-8 Crusader aircraft in 1:72 scale, according to the name for the E, J and P versions. Cut for the Academy kit.
In stock
7.16 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.