1:700 USS Quincy CA-39 (For Trumpeter 05748)

A veneer deck 1:700 for the American heavy cruiser USS Quincy CA-39 from Artwox Model is an accessory to a plastic kit. It brings a real wooden deck for the Trumpeter 05748 kit, with the laying of the planks printed on it and with a self-adhesive back.

Scale1:700
Manufacturer Artwox Model
Product EAN8591111000000

Responsibility details are not available.

15.96 €
13.19 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Wooden deck 1:700 for the heavy cruiser USS Quincy CA-39

Artwox Model offers this set as an aftermarket accessory for modelers who are building the heavy cruiser USS Quincy CA-39 in 1:700 scale. It is not a kit but a thin wooden veneer cut to the shape of the deck areas of the Trumpeter 05748 kit. On the face it has the laying of the planks printed on it, on the back a self-adhesive layer. Once it is glued on, the flat plastic grid disappears and is replaced by a surface with a pattern of wood of its own, which reacts to light differently from paint.

The real subject

The USS Quincy CA-39 was a heavy cruiser of the US Navy. Ships of this category built on a combination of strong gun armament in triple turrets, a decent speed and relatively light armor. They served to escort task groups, for gunfire support and for independent tasks. Typical on the model is the long wooden deck broken up by the barbettes of the turrets and by the superstructures, so the veneer has to seat very precisely.

Gluing and painting tips

Getting around the superstructures gives the most work. The procedure that proves itself: first check on the plastic part that all the projections and pins are sanded flat, because every little bump will appear in the veneer as a visible bulge. Lay the veneer on dry, mark the position of the barbettes with a pencil and only then take the film off. Around the circular barbettes it helps to lift the veneer and turn it rather than to press it in by force. Cut the overhangs away with a new blade guided along the edge of the plastic. Painting is not necessary, but a darker wash drawn along the planks brings out the gaps and adds depth. Matte varnish at the end evens the sheen out.

Who the set is for

  • For builders of this heavy cruiser in 1:700 scale
  • For modelers who want a precise deck without painting the planks by hand
  • For models with an open deck clearly visible from above
  • For those starting with aftermarket parts who do not want photo-etch yet

This is an accessory to a plastic kit, not a model of the ship. The kit, glue and paints are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. It is a wooden deck that you glue onto a plastic kit bought separately.

The deck areas are cut with cutouts for the barbettes. Before the film is taken off, check the position dry and mark it with a pencil.

Yes, that is recommended. Every pin or burr will show in thin veneer as a visible unevenness.

Under matte varnish the veneer keeps its shade for a long time. Without varnish it is sensitive to grease from the hands and to dust.

Last seen

Artwox ModelAW201081:700

1:700 USS Quincy CA-39 (For Trumpeter 05748)

A veneer deck 1:700 for the American heavy cruiser USS Quincy CA-39 from Artwox Model is an accessory to a plastic kit. It brings a real wooden deck for the Trumpeter 05748 kit, with the laying of the planks printed on it and with a self-adhesive back.
In stock
15.96 €
Art ScaleASKM350021:35

1:35 UH-1C one-sided painting mask for Academy

Masks for the UH-1C helicopter in 1:35, single-sided version are pre-cut self-adhesive painting masks from Art Scale. They serve for spraying the framing of the extensive cockpit glazing sharply; it is not a model or parts.
In stock
7.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.