1:350 SMS Viribus Unitis - masts, yards and other turned parts set - fits Combrig model

1:350 SMS Viribus Unitis - masts, yards and other turned parts set - fits Combrig model

21.16 €
Add to Cart

1:350 SMS Viribus Unitis - masts, yards and other turned parts set - fits Combrig model

A set of turned metal masts, yards and other parts for SMS Viribus Unitis in 1:350 scale.

Scale1:350
Manufacturer MASTER
Product EAN8591111128315

Responsibility details are not available.

21.16 €
17.49 € without VAT
2 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

MASTER 1:350 - masts, yards and turned parts for SMS Viribus Unitis

This accessory contains no gun barrels but turned metal masts, yards and other small turned parts for a model of the Austro-Hungarian battleship in 1:350 scale. It is not a kit. The set is cut for the Combrig kit; the manufacturer also makes a similar variant intended for a different kit, so check which version you are taking when ordering.

What the model gains

A mast is the most exposed part of a ship model. In plastic it is cast in two halves, so it has a lengthwise groove, once glued it tends to be slightly bent and when the rigging is tensioned it bends or cracks. A turned metal mast is perfectly straight, has a smooth taper from the foot to the tip and takes a tensioned thread without deforming. Metal yards hold a horizontal plane and do not give even after months in a display case. On a model of this era, where the rigging has a decisive share in the final impression, that is the difference between a finished piece and one that slowly twists.

Fitting and painting tips

Seat the foot of the mast in a drilled hole in the deck, not butt to butt: the metal part is heavier than a plastic one and a glued joint on a flat surface will not take the leverage. Drill the holes for the rigging in the yards beforehand, while the parts are still loose in your hand. Glue with gel grade cyanoacrylate or epoxy, which on a tall mast lets you set it truly vertical. Degrease the metal with alcohol and use a primer for metal, otherwise the paint will peel when the thread is tensioned. Tension the rigging of elastic thread only once the paint is dry and with a light touch: metal will take it, but the deck fittings will not.

Who the set is for

  • Builders of historical ship models in 1:350 scale.
  • Modelers who do rigging and need a firm, straight mast.
  • As an accessory to the metal barrels and etched sets for the same model.
  • Collectors who want a model to last for years without deforming.

The set is an accessory to a model, not a standalone kit. The ship model, glue and paints are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. This set contains masts, yards and other turned parts. The artillery barrels are a separate item.

It is cut for the Combrig kit. The manufacturer also makes a similar variant for a different kit, so check which version you are ordering.

A plastic mast has a parting groove, tends to be bent and bends when the rigging is tensioned. A turned metal part is straight and takes a tensioned thread.

Drill a hole in the deck and slide the foot into it. A butt joint will not take the weight and the leverage of a metal mast.

Last seen

MASTERSM3500771:350

1:350 SMS Viribus Unitis - masts, yards and other turned parts set - fits Combrig model

A set of turned metal masts, yards and other parts for SMS Viribus Unitis in 1:350 scale .
In stock
21.16 €
ReskitRSU32-01011:32

1:32 EJECTION SEAT MB MK.10LH FOR HAWK T.2,67,100/102,127,CT-155 (3D PRINTING)

Reskit 1:32 MB Mk.10LH ejection seat is a 3D-printed resin seat for models of the Hawk trainer aircraft (the T.2, 67, 100/102, 127 and CT-155 versions).
In stock
14.76 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.