URBAN CAMOUFLAGE FACE MASK 1

A two-layer fabric face mask with an urban camouflage pattern. The outer layer is 110 g polyester with a treatment, the inner one 140 g breathable polyester.

Manufacturer AK interactive
Product EAN8591111000000

Responsibility details are not available.

6.76 € 5.08 €
4.20 € without VAT
−25 % You save 1.68 €
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

A fabric mask with an urban pattern

This textile face mask came about at a time when a maker of modeling chemicals extended its range to accessories for everyday wear. The graphics were designed by the urban artist Carlos Corres and the pattern is based on the camouflage used in built-up areas: broken shapes in gray and beige tones that break up an outline.

The make-up of the material

The mask is sewn from two different fabrics. The outer layer is polyester of 110 grams per square meter with a water-repellent and antibacterial treatment, and the inner layer is breathable polyester of 140 grams. According to the supplier the fabric has UNE-0065/2020 certification, which is the Spanish standard for reusable hygienic masks.

Washing and service life

The supplier recommends washing the mask and states that it will keep its properties roughly to the twenty-fifth wash. Wash it after every wearing and let it dry out completely. Leave out fabric softener; it clogs the fibers and reduces breathability. Drying on a radiator or a hot cycle in a tumble dryer can damage the treatment of the fabric before the stated number of cycles is reached.

Wearing it

The cut follows the shape of the face and it is held by two elastics behind the ears. For the mask to hold its shape it has to bed down over the bridge of the nose and under the chin, and it should not be pulled about with the fingers while worn. Between wearings a fabric pouch will do it good; loose in a pocket with keys it gets dirty on both sides.

Who it is for

The mask suits work with sandpaper, sweeping a workshop or mixing loose materials, where what matters is coarse dust and comfort. It is not a filtering half mask with a replaceable cartridge and it will not replace a respirator when spraying paint; equipment intended for organic solvents belongs there.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

The supplier gives roughly twenty-five washes as the recommended use. After that number of cycles the treatment of the fabric gradually fades, but the mask itself will not fall apart.

It will not. For the aerosol from clear coats and for solvent vapors a half mask with a filter intended for organic vapors is what belongs. This mask is a textile accessory.

Freely in the air, away from a direct source of heat. A radiator and a hot cycle in a tumble dryer are not recommended, because the surface treatment of the outer fabric suffers at high temperatures.

Four graphics from the same maker exist, two urban and two classic camouflage ones. The cut and the make-up of the fabrics are the same on all of them; only the print changes.

Last seen

URBAN CAMOUFLAGE FACE MASK 1-25 %Stock ClearanceFavorite
AK interactiveAK9096

URBAN CAMOUFLAGE FACE MASK 1

A two-layer fabric face mask with an urban camouflage pattern. The outer layer is 110 g polyester with a treatment, the inner one 140 g breathable polyester.
16 left
6.76 €5.08 € You save 1.68 €
Dora WingsDOWI480571:48

1:48 Morane-Saulnier MS.406C.1 Finnish Aces

A short-run injection-molded kit of the Morane-Saulnier MS.406C.1 Finnish Aces in 1:48 scale from Dora Wings: the French fighter in Finnish service, with photo-etched parts and masks in the package.
In stock
35.96 €
1:48 Fi 156C-3/ C-5 Storch exterior-25 %Stock ClearanceFavorite
EduardED485811:48

1:48 Fi 156C-3/ C-5 Storch exterior

Eduard 1:48 Fi 156C-3/C-5 Storch exterior is a set of photo-etched parts for bringing out the exterior details of the model of the Fieseler Storch liaison aircraft. The model itself is not included in the package.
Last one!of 5
13.80 €10.36 € You save 3.44 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.