1:144 Harrier GR.1 / T.2 / AV-8A / AV-8C - Pitot Tube

1:144 Harrier GR.1 / T.2 / AV-8A / AV-8C - Pitot Tube

3.56 €
Add to Cart

1:144 Harrier GR.1 / T.2 / AV-8A / AV-8C - Pitot Tube

A pitot tube for the Harrier GR.1, T.2, AV-8A and AV-8C in 1:144 scale is a turned metal accessory from the Polish manufacturer MASTER. It replaces the coarse plastic part on the nose of a model.

Scale1:144
Manufacturer MASTER
Product EAN8591111000000

Responsibility details are not available.

3.56 €
2.94 € without VAT
9 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

The first-generation Harrier — pitot tube 1:144 (MASTER)

A turned metal accessory in 1:144 scale from the Polish manufacturer MASTER. It replaces the plastic pitot tube, that is, the dynamic pressure sensor, on models of the first generation of vertical take-off Harriers: the British single-seat GR.1, the two-seat T.2 and the American AV-8A and AV-8C. It is not a model of the aircraft but a small replacement part.

Why replace the plastic part

The pitot tube is among the thinnest external items on an aircraft and in 1:144 scale a plastic mold cannot make it slender enough: the part tends to be thick, often warped, and it breaks off easily while the model is handled. A turned metal part has the right profile, an accurate transition of diameters and far greater durability. In small scales in particular this is one of the few modifications that can be seen on a finished model at first glance.

The real subject

The Harrier was the first combat aircraft with vertical and short take-off to be taken into production service. Its design rests on an engine with vectoring exhaust nozzles, which make it possible to pass from a hover into horizontal flight without rotors that turn or wings that fold. The GR.1 version and the two-seat T.2 trainer served in the Royal Air Force, and the American AV-8A and the modernized AV-8C represent their counterpart on the other side of the Atlantic.

Fitting tips

Cut the plastic original off as close to the surface as possible and level the spot. Carefully drill a hole in the nose matching the diameter of the metal part: drill with a thinner bit first and increase the diameter gradually, as the plastic is thin in 1:144. Glue the part with super glue, with only a small drop applied on the tip of a toothpick. Before painting, degrease the metal with alcohol and use a primer for metal surfaces. Fit the tube at the very end, after varnishing and the decals, so that it is not damaged.

Who the set is for

  • Builders of Harrier models in 1:144 scale.
  • Modelers who finish small scales to display standard.
  • More experienced modelers used to drilling and working with super glue.
  • Those looking for a small upgrade with a visible effect.

This is not a kit of the aircraft but a metal accessory for one. The kit, paints and glue are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. It is a turned metal accessory, that is, a replacement for a single small part on a model. The kit itself has to be obtained separately.

The number of pieces is stated on the box of the set.

With super glue, that is, with cyanoacrylate. Glue for plastic does not hold on metal. A very small amount applied on the tip of a toothpick is enough.

The part is glued into a drilled hole, so it is fairly universal, but compare the shape of the nose in advance all the same.

Last seen

MASTERAM1440361:144

1:144 Harrier GR.1 / T.2 / AV-8A / AV-8C - Pitot Tube

A pitot tube for the Harrier GR.1, T.2, AV-8A and AV-8C in 1:144 scale is a turned metal accessory from the Polish manufacturer MASTER. It replaces the coarse plastic part on the nose of a model.
In stock
3.56 €
VallejoVALT04004

Flexi Sanders Dual-Grit (80x30x12mm)

A thicker sanding sponge 80 x 30 x 12 mm with two grits. Intended for large flat areas.
In stock
5.56 €
VallejoVALT01002

Set of 20 Drill Bits, No 61-80

In stock
17.16 €
MineshimaMNS-L10-12

Drill Bit 1.2mm L10-12

The Mineshima 1.2 mm modeling drill bit is intended for drilling larger holes for pins, dowels and reworking plastic parts in a pin vise.
In stock
3.96 €
ICMICM358311:35

1:35 Model T Runabout 1918

An injection-molded plastic kit of the Model T Runabout 1918 in 1:35 scale from ICM. The subject is a light two-seat Ford with an open body and a folding fabric top.
In stock
24.76 €
MontexMXKAM321741:32

1:32 SPITFIRE IX

Masking set for the Spitfire Mk.IX in 1:32 scale. Besides masks for the glazing and three national insignia masks it contains decals and two metal barrels for the 20 mm Hispano cannons.
In stock
19.96 €
MontexMXKAM481431:48

1:48 P-47D Bubbletop

The Republic P-47D with the teardrop canopy in 1:48 scale and with it eight turned muzzles for the heavy Browning machine guns, a canopy mask, two sets of national insignia masks and decals. Prepared for the Tamiya kit.
In stock
19.16 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.