29.–30. 10. z technických důvodů zavřeno. / Closed 29–30 October for technical reasons.

1:32 A-20G Havoc

A-20G Havoc 1:32 is a set of painting masks from the manufacturer Eduard for a model of the Douglas A-20G Havoc attack aircraft. The masks are stuck straight onto the clear part and do away with cutting tape.

Scale1:32
Manufacturer Eduard
Product EAN8591111427098

Responsibility details are not available.

12.40 € 9.32 €
7.70 € without VAT
−25 % You save 3.08 €
1 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

The A-20G Havoc masking set in 1:32 scale

This item is not an airplane model but a set of pre-cut painting masks from the manufacturer Eduard. The masks are stuck straight onto the clear part of the model and define the areas that are to stay transparent, while the glazing frames are sprayed with paint. That does away with the most tedious part of working on a cockpit: cutting strips from masking tape by hand, measuring out and guessing whether the edge is straight. The masks have a shape derived from the particular part, so they sit on the frame and the paint edge is sharp.

The real subject

The Douglas A-20 Havoc was an American twin-engine attack and bomber aircraft. The A-20G version did not have a glazed nose for a navigator but a solid nose with gun armament, because it was intended for attacks on ground targets from low altitude. The glazed pilot's canopy and the gun positions behind it make the model in 1:32 scale a fairly demanding piece to mask.

How to use the masks

First wash the clear part and let it dry perfectly; grease from your fingers holds a mask worse than a clean surface. Lift the mask off the sheet with pointed tweezers or a wooden stick, seat it in place and press the edges down with a toothpick, so that no paint gets under the edge. Spray the paint in thin coats; one heavy coat is drawn under the edge of the mask more easily than two fine ones. Take the mask off while the paint is freshly dried, not after several days, when the edge goes brittle and may tear away. On intricately shaped surfaces it helps to warm the mask lightly once it is in place.

Who the set is for

  • Modelers building the Havoc in 1:32 scale, where the glazing is extensive
  • Those who do not want to spend an evening cutting tape and measuring out frames
  • Builders who care about a sharp edge between the frame and the clear surface
  • Beginners for whom masking a cockpit is the biggest obstacle

The masks are an accessory to a plastic kit. The model itself and the paints are not part of the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. This is a set of painting masks for a plastic A-20G Havoc kit in 1:32 scale, which you obtain separately.

Best shortly after the paint has dried. After a longer time the edge of the paint goes brittle and a piece of the coat may be torn away when peeling.

The most common cause is an edge that has not been pushed down or too heavy a coat of paint. So press the edges down with a toothpick and spray thinly, over several passes.

Yes, Eduard makes a set designated TFace for the same type, which is meant for the inner side of the glazing as well. In the manufacturer's range it is a separate item.

Last seen

1:32 A-20G Havoc-25 %Stock ClearanceFavorite
EduardJX3151:32

1:32 A-20G Havoc

A-20G Havoc 1:32 is a set of painting masks from the manufacturer Eduard for a model of the Douglas A-20G Havoc attack aircraft. The masks are stuck straight onto the clear part and do away with cutting tape.
Last one!of 3
12.40 €9.32 € You save 3.08 €
MN-hobby16F0041:16

1:16 Dopravní stráž 1939

1:16 traffic guard 1939 is a figure of a member of the traffic guard as he looked in 1939, offered in 1:16 scale by MN-hobby.
In stock
11.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.