1:72 Lockheed-Martin F-35B Lightning II canopy & undercarriage

1:72 Lockheed-Martin F-35B Lightning II canopy & undercarriage

12.76 €
Add to Cart

1:72 Lockheed-Martin F-35B Lightning II canopy & undercarriage

1:72 Lockheed Martin F-35B Lightning II — canopy and undercarriage is a photo-etched set from Eduard for an F-35B model in 1:72 scale; it is not a kit but a set of metal parts for two particular areas of the model.

Scale1:72
Manufacturer Eduard
Product EAN8591111000000

Responsibility details are not available.

17 € 12.76 €
10.55 € without VAT
−25 % You save 4.24 €
1 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

1:72 Lockheed Martin F-35B Lightning II — Eduard photo-etched set for the canopy and the undercarriage

A photo-etched set from the Czech firm Eduard aimed at two areas of a model of the Lockheed Martin F-35B Lightning II in 1:72 scale — the surroundings of the cockpit glazing and the undercarriage. It is precisely there that injection-molded plastic tends to be coarsest: the framing of the canopy and the fine stiffeners and subdivisions of the undercarriage bays and legs cannot be impressed in a mold at a realistic thickness. The set is intended for the build of a basic plastic model of the corresponding type and scale; it is not a model or a kit.

The real subject

The Lockheed Martin F-35B Lightning II is the variant of the fifth-generation combat aircraft intended for short takeoff and vertical landing. Unlike the other versions it carries a lift fan behind the cockpit driven from the single engine and has a deflecting rear nozzle, thanks to which it can operate from short strips and from the decks of smaller ships. The design is pursued with the emphasis on a low radar signature and on merging the sensors into a single picture for the pilot.

Building tips

On modern machines with few visible subdivisions, clean work is essential — separate the photo-etched parts with a sharp knife on a hard surface and polish the edges after cutting. Make the folds along the etched line, ideally in a bender. Degrease the metal and coat it with a primer, otherwise the paint will not hold. Glue with super glue in the smallest of doses or with slow-setting epoxy. Fit the parts into the undercarriage bays before you close the fuselage and, conversely, leave the elements around the glazing until after clear coating, so that they are not damaged while masking and sanding.

Who the set is for

  • Modelers who build the F-35B in 1:72 scale and want a truer cockpit and undercarriage.
  • Builders of modern aircraft with experience of working with photo-etch.
  • Those preparing a model for a display case or a competition.
  • Owners of the basic kit of the corresponding type and scale.

It is a modeling accessory, not a kit. The base model, paints and glue are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. It is a photo-etched set for two particular areas of a model — the surroundings of the cockpit glazing and the undercarriage. The basic plastic F-35B kit in 1:72 scale is bought separately.

The elements for the undercarriage bays before the fuselage is closed, and the parts around the glazing at the end of the build, so that they are not damaged while sanding and masking.

They are the places where the detail shows most and where injection-molded plastic comes out unrealistically thick. Metal sheet allows a truer thickness there.

Yes, degreasing and a coat of primer. On bare metal the paint holds poorly and rubs off during handling.

Last seen

1:72 Lockheed-Martin F-35B Lightning II canopy & undercarriage-25 %Stock ClearanceFavorite
EduardED727001:72

1:72 Lockheed-Martin F-35B Lightning II canopy & undercarriage

1:72 Lockheed Martin F-35B Lightning II — canopy and undercarriage is a photo-etched set from Eduard for an F-35B model in 1:72 scale; it is not a kit but a set of metal parts for two particular areas of the model.
Last one!
17 €12.76 € You save 4.24 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.