LAST CHANCE! 20% OFF Ends Tonight!

1:35 Pz.kPfw. IV Ausf F2/G (For DRAGON 6360)

Voyager Model 1:35 Pz.Kpfw. IV Ausf. F2/G is a photo-etched add-on set for a plastic kit you already own, not a standalone model. The brass photo-etched parts replace the thin sheet-metal areas of the tank, which injection-molded plastic handles only in coarser form. Intended for the Dragon 6360 kit.

Scale1:35
Manufacturer Voyager Model
Product EAN8591111000000

Responsibility details are not available.

21.96 €
18.15 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Pz.Kpfw. IV Ausf. F2/G 1:35 — photo-etched set from Voyager Model

An aftermarket detail set from Voyager Model in 1:35 scale. It is prepared for the Dragon 6360 plastic kit and replaces some of its parts with photo-etched brass sheet. It is not a tank kit but an accessory for the build. The scope of the set follows from the contents of the package and the enclosed instructions.

The real subject

The Pz.Kpfw. IV Ausf. F2 and the Ausf. G that followed were versions of the German medium tank of the Second World War which received a long-barreled 7.5 cm gun in place of the original short weapon meant for infantry support. That change turned the Pz.Kpfw. IV into a full-fledged anti-tank asset and set the course for the further development of the type. Vehicles of the two versions differed in details of the muzzle brake, the vision ports and the add-on armor.

Degreasing and primer, or the paint will not hold

Photo-etched brass comes from the factory with a thin layer of process oil, plus grease from your fingers. Neither paint nor primer will adhere to such a surface, and they come away at the first handling or masking. The procedure is simple and cannot be skipped: wash the parts while still on the fret in warm water with dish soap, or wipe them with alcohol, from then on touch them only with tweezers or through a glove, and lay on a thin primer for metal. Only then does the paint follow. If you are gluing the photo-etched parts on after the model is painted, sand the paint away down to the plastic at the contact point, because cyanoacrylate holds considerably worse on paint than on a bare surface.

Who the set is for

  • Builders of German armor in 1:35 scale
  • Modelers bothered by plastic fenders and covers that are heavy for the scale
  • More experienced builders with tweezers, a scalpel and cyanoacrylate
  • Those building for a display case or a competition who also care about what can be seen from above

The set is an accessory for a plastic kit and is not a standalone model. The kit, glue, paints and tools are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

According to the name it is prepared for both versions. The specific steps for each are in the instructions, so always try the parts dry first.

It is not. It is a photo-etched accessory for a plastic kit, which has to be bought separately.

Neither primer nor paint grips on the factory grease, and the finish flakes off later. Washing with dish soap or a wipe with alcohol before painting is enough.

A sharp scalpel or photo-etch scissors, tweezers, cyanoacrylate and ideally a bending tool. Without a bender the edges can be managed with a steel ruler.

Last seen

Voyager ModelPE351411:35

1:35 Pz.kPfw. IV Ausf F2/G (For DRAGON 6360)

Voyager Model 1:35 Pz.Kpfw. IV Ausf. F2/G is a photo-etched add-on set for a plastic kit you already own, not a standalone model. The brass photo-etched parts replace the thin sheet-metal areas of the tank, which injection-molded plastic handles only in coarser form. Intended for the Dragon 6360 kit.
In stock
21.96 €
Plastruct PLT90658

Open Web Truss Warren (1 pcs) H-25,4mm W-46,8mm T-7,9mm L-300mm

Plastruct Open Web Truss Warren — a plastic truss girder, 1 pc is a building semi-finished material with a Warren truss pattern. Height 25.4 mm, width 46.8 mm, thickness 7.9 mm, length 300 mm.
In stock
7.96 €
Plastruct PLT90023

I Beam (1 pcs) H 3.2, W 1.6, T 0.6, L 375 mm

Plastruct I Beam — a plastic I profile (double T beam), 1 pc is a raw material for modelers. Height 3.2 mm, flange width 1.6 mm, thickness 0.6 mm, length 375 mm.
In stock
1.80 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.