1:48 Mi-35M masks

Mi-35M – a masking set in 1:48 (SX-Art) is a set of pre-cut templates for a model of this combat helicopter. It is not a model but an add-on that makes masking easier when painting.

Scale1:48
Manufacturer SX-Art
Product EAN8591111463720

Responsibility details are not available.

5.56 €
4.60 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Mi-35M, a masking set in 1:48 (SX-Art)

Pre-cut masking templates from the SX-Art brand for a model of the Mi-35M helicopter in 1:48. The helicopter has a lot of glazing, a broken-up fuselage and plenty of small protrusions, so masking by hand is slow and mistakes come easily. The templates shorten the work and hold the shapes the same on both sides of the model. It is not a kit; the model itself has to be had.

The real subject

The Mi-35M is an upgraded attack helicopter derived from the Mi-24 line, with a tandem cockpit and short stub wings. It is recognized from the older machines among other things by its shortened wings, non-retractable landing gear and a revised front section with electro-optical equipment. The changes in the shape of the nose and in the fittings carry straight over into where the masking runs.

Where the pattern begins and ends

Modern machines tend to wear a pattern with hard, geometrically led fields. On a helicopter that shows above all where a boundary runs across the engine covers, across the doors and around the wing roots. The pattern has to carry on even across protrusions, antennas and fittings on the nose, which is almost impossible to keep symmetrical when masking by hand. A template solves that problem. Once the masks are on, spray thinly and perpendicular to the edge, so that paint does not run under the edge on rounded surfaces. Around small protrusions it pays to seal a mask down afterward with a narrow strip of tape. Once unmasked, go over the sharp edge with a very thinned shade, so that the transition does not read as a stuck-on strip, and add a few blotches freehand if you are building a machine with a more irregular finish.

Tips and who the set is for

  • For builders of an Mi-35M helicopter model in 1:48
  • For modelers who want a symmetrical pattern across the covers, the doors and the wing roots
  • Before buying, compare the shape of the parts with the kit you have
  • Apply the paint in thin coats and at lower pressure
  • Take the mask off while the paint is still flexible

This is a masking add-on, not a kit. The model, paints and glue are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not. It is a masking add-on for painting. The Mi-35M model has to be had separately.

The name does not give the target kit. Before buying, we recommend comparing the shape of the glazing and the parts with the model you have.

The upgraded machine has its nose and its fittings handled differently, so the boundaries of the pattern run elsewhere. Masks cut for the older version need not fit.

Press the edge of the mask down, seal small protrusions with a narrow strip of tape and spray thinly, perpendicular to the edge.

Last seen

SX-ArtSXA481091:48

1:48 Mi-35M masks

Mi-35M – a masking set in 1:48 (SX-Art) is a set of pre-cut templates for a model of this combat helicopter. It is not a model but an add-on that makes masking easier when painting.
In stock
5.56 €
ELEFANTEL352111:35

1:35 IDF plastic jerry cans - gasoline, 10 pcs.

ELEFANT 1:35 IDF plastic gasoline cans (10 pcs) is a resin set of ten modern Israeli fuel cans of the jerry can type for dioramas and models of military hardware.
In stock
7.96 €
Art ScaleASKM481811:48

1:48 Westland Sea King HAS.1/HAS.5/HU.5 double-sided express fit mask for Airfix

A double-sided express fit masking set in 1:48 scale for a model of the Westland Sea King naval helicopter in the HAS.1, HAS.5 and HU.5 versions. It covers the glazing from the outside and from the inside. The cut follows the parts of the Airfix kit.
In stock
11.56 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.