1:32 A-10C 3D-Printed and coloured Interior on decal paper

1:32 A-10C 3D-Printed and coloured Interior on decal paper

19.76 €
Add to Cart

1:32 A-10C 3D-Printed and coloured Interior on decal paper

A-10C, a 3D-printed colored interior on decal paper in 1:32 scale from Quinta Studio takes the place of laborious painting of a modern cockpit.

Scale1:32
Manufacturer Quinta Studio
Product EAN8591111000000

Responsibility details are not available.

26.36 € 19.76 €
16.33 € without VAT
−25 % You save 6.60 €
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

A-10C, a 3D-printed interior on decal paper in 1:32 scale

A set of 3D-printed and pre-painted interior elements on decal paper for a model of the A-10C ground attack aircraft in 1:32 scale from Quinta Studio. It is not a kit of an aircraft or a set of parts to be glued but an accessory applied by the wet method like a decal. The elements have a real relief and color from the factory, so the work is shortened to preparing the surface and seating them precisely.

The real subject

The A-10C is the upgraded form of the American single-seat ground attack aircraft known as the Thunderbolt II. The upgrade concerned above all the cockpit equipment, where multifunction displays were added and the controls concentrated on the control column and the throttle section. The layout of the pilot's area therefore differs visibly from the older A-10A version, and interior sets are made separately for the two forms.

Placing it in the sequence of work

With accessories of this kind the order of the steps decides. The interior is first assembled and sprayed with a base color, which has to cure thoroughly, because a decal laid on paint that has not dried may later wrinkle. Then comes gloss varnish, and only after that do the decal elements have their turn. If the set is combined with other accessories, such as masks or a resin seat, the resin parts are fitted first as a rule and the decals only onto finished surfaces. The element is cut off, briefly soaked in lukewarm water, slid into place, and the water is pressed out from beneath it by a soft brush or a cotton bud drawing from the center. A decal softener has no place in the procedure, as it would attack the printed resin. No pressure is put on the relief. Once dry the whole interior is evened out with a matte varnish and only then is the cockpit closed up.

Who the set is for

  • Builders of ground attack aircraft in 1:32 scale
  • Modelers who want a modern cockpit with displays without hand painting
  • Those who combine several accessories and are looking for the element that is applied fastest
  • Builders of models displayed with the canopy open

This is an accessory for a plastic kit, not a model of the aircraft. Check the match with your kit before buying. Paints and glue are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It is not suitable. The cockpit of the upgraded version differs from the older one in the layout of the panels, which is why sets are made separately for each form.

First the resin parts and their painting, then gloss varnish once they have cured, and only at the end the decal elements. Matte varnish comes last of all.

On paint that has not dried a decal may later wrinkle or bubbles may appear under it. The difference of a few hours of drying is worth it.

The extent of the set is given on the packaging. The surrounding surfaces of the cockpit always have to be painted separately.

Last seen

1:32 A-10C 3D-Printed and coloured Interior on decal paper-25 %Stock ClearanceFavorite
Quinta StudioQD320731:32

1:32 A-10C 3D-Printed and coloured Interior on decal paper

A-10C, a 3D-printed colored interior on decal paper in 1:32 scale from Quinta Studio takes the place of laborious painting of a modern cockpit.
5 leftof 6
26.36 €19.76 € You save 6.60 €
Q Posket - Hatsune Miku - V4X Style Ver. B-25 %Stock ClearanceFavorite
BandaiBANBP18912

Q Posket - Hatsune Miku - V4X Style Ver. B

Q Posket Hatsune Miku V4X Style Ver. B is a finished collector figure from the Q Posket line. It comes painted from the factory and all you do is display it.
Last one!
29.56 €22.16 € You save 7.40 €
EduardED6723441:72

1:72 Messerschmitt Bf-109G radio compartment PRINT

Bf 109G radio compartment PRINT 1:72 is a 3D-printed resin detail set from Eduard that refines the fitting out of the radio compartment in the fuselage on a Messerschmitt Bf 109G model.
In stock
6.80 €
PolákPOL9188

Nízké keře - kvetoucí - Modré 14ks

Low flowering bushes Blue 14 pcs from Polak is a set of ready-made flowering bushes for dioramas and layouts.
In stock
12.36 €
Black Dog modelBDT480731:48

1:48 Heavy Tank Destroyer Elefant - Accessories Set (for Tamiya kits)

1:48 Heavy Tank Destroyer Elefant - Accessories Set brings resin equipment from Black Dog model for a model of the German heavy tank destroyer.
In stock
18.36 €
AberABREVS041:35

1:35 PANZER IV Ausf.D (PzKpfw IV)

Aber 1:35 – a detail set for the German PzKpfw IV Ausf.D tank brings together photo-etched brass parts and a turned metal barrel for the short gun. It is not a kit.
In stock
33.40 €
1:48 Hs 123 seatbelts STEEL-25 %Stock ClearanceFavorite
EduardFE8601:48

1:48 Hs 123 seatbelts STEEL

Eduard 1:48 Hs 123 seat belts (STEEL) is a colored photo-etched belt set with a steel effect for the model of the Henschel Hs 123 ground-attack biplane. The model itself is not included in the package.
Last one!of 3
6 €4.52 € You save 1.48 €
AberABR350541:35

1:35 Pz.Kpfz. III, Ausf. M/N

Aber Pz.Kpfw. III Ausf. M/N is a photo-etched metal detail set in 1:35 for refining a model of the German Panzer III medium tank in the late M and N versions.
In stock
16.60 €
FLEX-I-FILEFFCS320

Cone Tip Sander with Peel & Stick Abrasive Pieces 320 Grit

The FLEX-I-FILE cone tip sander in 320 grit is an applicator handle with a cone tip and a set of peel and stick abrasive pieces for preparing the surface in places an ordinary sanding block cannot reach.
In stock
7.56 €
HasegawaHAJT361:48

1:48 Nakajima Ki-44-II Hei Shoki (Tojo)

The Nakajima Ki-44-II Hei Shoki (Tojo) is a plastic kit of the Japanese single-engine interceptor of the Second World War in 1:48 scale from Hasegawa.
In stock
23.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.