1:32 F-35A Tails For Italeri

Replacement tail surfaces for a large model of the fifth-generation aircraft in 1:32 scale, cast in resin. Intended for Italeri kits.

Scale1:32
Manufacturer Kopecky Scale Models
Product EAN3391111783599

Responsibility details are not available.

27.16 €
22.45 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

Canted fins and why they matter

Both vertical surfaces of the F-35A are canted outwards and their leading and trailing edges meet the longitudinal axis at angles meant to deflect radar waves away from the source. The shape is therefore functional rather than pleasing, and even a small deviation in the angle is visible on a finished model. That is precisely why the tail surfaces are replaced more often on this type than on other machines. The add-on is intended for Italeri kits.

Close to central Europe

The type is ceasing to be an exotic American matter. The Czech Republic decided to acquire twenty-four of these machines and the contract was signed in 2024; Poland ordered thirty-two pieces earlier still and its aircraft began arriving in Europe sooner. Within a few years the model will therefore stop being a model of foreign hardware.

Installation

The surfaces are glued home into seats in the rear part of the fuselage and it is essential to watch that both meet at the same angle; the eye notices asymmetry at once. It works well to glue one surface, let it cure and only then measure the position of the second against a common horizontal plane.

An add-on that counts on a model

The package deals solely with the tail surfaces for the Italian brand's kit in the same scale. Within this maker's range it sits alongside the larger sets of pylons and drop tanks in extent, and the scope of the casting matches that. The painting calls for patience, because the finish of the original is matte and uneven and a uniform spray will not capture it.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

Injection-molded parts tend to be thicker at the edges and the angles need not fit exactly. A casting is thinner and has sharper edges.

It is not. These are replacement parts for a kit, which has to be bought separately.

Glue them one at a time, with a pause for curing, and measure the position of the second surface against a common horizontal plane under the model.

Yes. Besides the American units, several European states are bringing it into service, including the Czech Republic and Poland.

It is intended for Italeri kits.

Last seen

Kopecky Scale ModelsKSM320091:32

1:32 F-35A Tails For Italeri

Replacement tail surfaces for a large model of the fifth-generation aircraft in 1:32 scale, cast in resin. Intended for Italeri kits.
In stock
27.16 €
Aires/AerobonusAER4801601:48

1:48 Soviet Fighter Pilot with seat for I-153

Resin figure of a Soviet fighter pilot with a seat for the Polikarpov I-153 in 1:48 scale from the Aerobonus brand. A figure to be painted, not a model.
In stock
7.20 €
SX-ArtSXA482131:48

1:48 Paint mask AH-1Z Viper (KITTYH/ZIMI)

Self-adhesive painting masks of kabuki film for a model of the Bell AH-1Z Viper attack helicopter in 1:48 scale. For spraying the frames of the extensive cockpit glazing cleanly.
In stock
5.96 €
PANZER ARTFI35-0021:35

1:35 Waffen-SS camo overall tanker No.2

1:35 Tanker in a camouflage overall, variant No. 2 is a resin figure from the PANZER ART brand made for an open hatch or for a diorama.
In stock
13.96 €
SBS ModelSBS721001:72

1:72 F2A-1 Buffalo - Superdetail Set (for Hasegawa & Hobby 2000 Kits / Resin + 3D-Printed + PE Parts)

Detail set for the Brewster F2A-1 Buffalo fighter in 1:72 scale, built for the Hasegawa and Hobby 2000 kits. It combines cast resin parts, 3D-printed parts and photo-etch.
In stock
54.76 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.