1:48 F-4J/S Exhaust nozzles

The exhaust nozzles for the F-4J/S in 1:48 scale from the LP Models brand are a resin accessory that replaces the simplified nozzles from a Phantom kit with a detailed casting.

Scale1:48
Manufacturer LP Models
Product EAN8591111000000

Responsibility details are not available.

6.36 €
5.26 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

F-4J/S exhaust nozzles: a 1:48 resin set (LP Models)

This is not a model of an aircraft but an accessory. The set contains exhaust nozzles cast in resin in 1:48 scale, intended for models of the Phantom II fighter in the J and S versions. On this type the nozzles are among the most prominent details of the rear end, and the plastic parts from ordinary kits tend to be thick-walled and only suggested; a resin casting offers a thin edge and internal structure that is visible from behind. The manufacturer also carries a variant for the older Phantom versions in its catalog, so take care to choose the nozzles that correspond to your version.

Why the J and S versions

The Phantom II was built in a number of versions that differed among other things in their powerplants and with them in the external form of the exhaust section. The nozzles are therefore not interchangeable between versions, and a mismatch can be seen on a finished model. The J and S versions are related: the S came about through the modernization of older machines, so the same solution of the rear end applies to both. Check which particular subject you are building against period photographs.

Building and painting tips

First wash the parts in warm soapy water, so that no mold release from the mold is left on the surface. Cut the casting blocks off with a thin saw and finish the surface wet and with respiratory protection. It is glued with cyanoacrylate; cement for plastic has no effect on resin. Nozzles are easier to paint separately, off the model: a base in a dark metallic shade, then metallic shades applied in thin, irregular coats and complemented by heat tinting toward the edge. Darken the inside of the nozzle and bring the ribs out with a fine dry brush. Before gluing it in finally, try the fit dry: on some kits the opening in the rear end has to be opened up.

Who the set is for

  • Modelers building the Phantom II in the J and S versions in 1:48 scale
  • Builders who dislike the thick-walled plastic nozzles from a kit
  • Those interested in painting metal and heat-stressed surfaces
  • Modelers with basic experience of resin accessories

This is an accessory set, not a model in its own right. The base kit, glue and paints are not included in the package.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. The exhaust section differs between versions and the difference shows on a finished model. For the older versions the manufacturer carries a separate set.

No. It is an accessory that replaces a part from the base kit. The model of the aircraft itself is not included in the package.

With cyanoacrylate glue. Cement for plastic does not bite into resin and the joint would not hold.

Often it is enough to clean up the opening in the rear end, but on some kits it has to be opened up slightly. Always try the fit dry before gluing.

Last seen

LP ModelsLP-480141:48

1:48 F-4J/S Exhaust nozzles

The exhaust nozzles for the F-4J/S in 1:48 scale from the LP Models brand are a resin accessory that replaces the simplified nozzles from a Phantom kit with a detailed casting.
In stock
6.36 €
Artwox ModelBW10022A1:350

1:350 WWII U.S. Navy Battleship BB-63 Missouri

In stock
41.16 €
Mr.PaintMRP165

Grey Green (Mig 23, Mig 29, Su 22, Su 25)

The modeling acrylic lacquer Mr.Paint Grey Green (MiG-23, MiG-29, Su-22, Su-25) — the gray-green shade of the tactical camouflage of Soviet aircraft, ready for airbrush application.
In stock
5.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.