1:48 MiG-23 (Flogger) - Pitot Tube (all variants except MLD version)

1:48 MiG-23 (Flogger) - Pitot Tube (all variants except MLD version)

5.56 €
Add to Cart

1:48 MiG-23 (Flogger) - Pitot Tube (all variants except MLD version)

1:48 MiG-23 (Flogger) pitot tube for all versions except the MLD is a turned metal replacement part by the brand MASTER. It is not a kit but a detail for a model that is already built.

Scale1:48
Manufacturer MASTER
Product EAN8591111123068

Responsibility details are not available.

5.56 €
4.60 € without VAT
1 pcs in stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

A metal pitot tube for the MiG-23 in 1:48 scale

This accessory by the Polish brand MASTER replaces the plastic air data tube on the nose of a model of the MiG-23 fighter with variable-geometry wings. According to its name the part is cut for all versions except the MLD variant, for which MASTER makes a separate item. It is worth checking that distinction before buying, because the tube differs between the two groups of versions.

What the metal part brings

The air data tube of the MiG-23 is long, slender and stepped, exactly the kind of shape injected plastic cannot handle. A plastic part tends to have a parting line along its whole length, it is often slightly bent, and the individual steps of diameter are softened. Turned metal holds the sharp transitions of diameter, it is perfectly straight and concentric and it has a real opening in the front. There is a practical, mechanical advantage as well: a metal tube survives being touched while the model is handled, whereas a plastic one breaks in this place again and again.

Fitting and painting tips

Cut the plastic original off as close to the fuselage as possible and level the surface with a file. Drill the hole with a micro drill bit, increase the diameter in small steps and keep trying the fit. Glue with cyanoacrylate or epoxy; ordinary cement for plastic does not work here. Check the axis from two directions, from above and from the front. Degrease the metal with alcohol before painting and use a primer for metal surfaces, otherwise the paint will not hold on the smooth surface and will rub off at the first touch. An alternative is to leave the metal in its natural shade and simply darken it by blackening. Glue the tube in only once painting and decals are finished.

Who the part is for

  • Builders of the MiG-23 in 1:48 scale other than the MLD variant
  • Modelers who want accurate steps of diameter on the air data tube
  • Display models on which the nose is the most visible part of all
  • Anyone dealing with a crooked or broken plastic tube

An accessory for a base model, not a standalone kit. The model, glue and paints are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

It does not. According to its name it is intended for all versions except the MLD, for which a separate item exists.

It is not. It is a single metal replacement detail that is glued onto a model that is already built.

Cyanoacrylate or a two-part epoxy. Cement for plastic will not bond metal.

It does not, but if you do paint it, degrease the surface with alcohol and apply a primer for metal. Otherwise the paint will chip off during handling.

Last seen

MASTERAM480581:48

1:48 MiG-23 (Flogger) - Pitot Tube (all variants except MLD version)

1:48 MiG-23 (Flogger) pitot tube for all versions except the MLD is a turned metal replacement part by the brand MASTER. It is not a kit but a detail for a model that is already built.
In stock
5.56 €
ReskitRSU48-02971:48

1:48 Vought A-7 (E,D) Corsair II exhaust nozzle

The resin 3D printed Reskit exhaust nozzle for the A-7 Corsair II 1:48 , for experienced modelers; a faithful replacement for the engine nozzle of the A-7E/D variant.
In stock
19.56 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.