1:700 NEW JERSEY BB-62 (For Tamiya 31614)

The Artwox Model 1:700 veneer deck for the American battleship USS New Jersey BB-62 replaces the plastic deck with wood with the laying of the planks printed on it. It is an accessory to a kit, not a model. Intended for the Tamiya 31614 kit.

Scale1:700
Manufacturer Artwox Model
Product EAN8591111000000

Responsibility details are not available.

15.96 €
13.19 € without VAT
In stock
Free shipping on orders over 1,000 czk in czech republic Personal pickup in Prostějov 14-day returns

About product

New Jersey BB-62 1:700 — an Artwox Model wooden deck

A self-adhesive sheet of natural veneer, pre-cut to the shape of the deck areas of a battleship model in 1:700 scale. The pattern of the laying of the planks is printed, so the most tedious part of the work is gone: tapping the gaps out with a scriber or painting them by hand. The veneer is stuck onto the plastic deck of the kit, which has to be obtained separately. The extent of the parts differs between sets, and the number of segments is stated on the box of the set. The set is intended for the Tamiya 31614 kit.

The real subject

The USS New Jersey BB-62 belonged to the American Iowa class, the last generation of American battleships. She was marked by a long slender hull, high speed and main armament of 406 mm guns in three turrets. The ship was taken into service in 1943 and over the following decades went through several periods of active service and reserve, including later modernizations. Today she is preserved as a museum ship. The expansive wood-covered decks are among her most prominent features, which makes a veneer deck one of the most effective accessories on this type in particular.

Application tips

Most of the work goes on getting around the superstructures, the barbettes and the hatches. Proceed by trying the part dry first and marking on the back with a felt-tip pen the places where it needs trimming. On the circular cutouts around the turrets a circle cutter proves itself, or patient removal in small pieces with a new blade: the veneer is thin and a blunt knife tears it rather than cuts it. It is better to leave the overlaps a hair too large and to trim them on the model along the real edge. Score the inner corners before you settle the part, otherwise the wood will crease in them.

Who the set is for

  • Builders of American battleships in 1:700 scale
  • Modelers who want a realistic wooden deck without painting it by hand
  • Anyone interested in display models with large visible areas
  • Those adding photo-etched railings and other equipment to a model

This is an accessory to a plastic kit, not a model. The kit, glue, paints and photo-etched parts are not included in the package, unless stated otherwise.

Reviews

No reviews yet Have you built this one? Tell other modellers how it went and help them choose.

Forum

Naši poradci a znalci sortimentu jsou připraveni odpovídat na Vaše dotazy (Po–Pá, 8–18 hod).
Zeptejte se na co potřebujete, odpovíme co nejdříve.

Texts from customers in the advice section reflect solely the opinions and views of the customers. MNF trade s.r.o. does not approve or verify customer texts in advance.

There are no questions here yet. Be the first to ask!

FAQ

No. The decks are cut to the plan of a particular kit, and for this ship several variants exist. Before ordering, compare the description of the variant with the model you are building.

Always with a new sharp blade or a circle cutter, in small steps. The veneer is thin and a blunt edge tears it. Try the opening dry first and only then remove the backing film.

It is recommended. A matte or satin varnish protects the wood against damp and dirt during further work and at the same time evens the sheen out with the surrounding sprayed areas.

Last seen

Artwox ModelAW200261:700

1:700 NEW JERSEY BB-62 (For Tamiya 31614)

The Artwox Model 1:700 veneer deck for the American battleship USS New Jersey BB-62 replaces the plastic deck with wood with the laying of the planks printed on it. It is an accessory to a kit, not a model. Intended for the Tamiya 31614 kit.
In stock
15.96 €
ZvezdaZV61641:350

1:350 Soviet Armored Boat 1125

Injection-molded plastic kit of the Soviet armored gunboat Project 1125 1:350 from Zvezda. A simple snap-fit model that needs no glue.
In stock
3.96 €
Loading, please wait...

Setting consent to personalization

With your consent, we may use the information below for the following purposes or share it with selected partners. You can adjust your settings for individual purposes (types of processing) and confirm your choice with the "Save settings" button:

Always active

Necessary cookies

These are technical files that are necessary for the correct behavior of our website and all its functions. They are used, among other things, to store products in the shopping cart, display products on request, control filters, personal settings and also set consent to the use of cookies. Your consent is not required for these cookies and it is not possible to remove it.

Analytical cookies

They count website traffic and, by collecting anonymous statistics, enable the operator to better understand their visitors and thus constantly improve the site.

Marketing cookies

They collect information to better tailor advertising to your interests, both on and off this website.

Setting consent to personalization

To make it easier for you to browse the site, to offer you customized content or advertising, and to analyze traffic anonymously, we use cookies that we share with our partners for social media, advertising, and analytics. You can adjust their settings with the "Edit settings" link and you can change it at any time in the footer of the website. You can find more detailed information in our Policy on the protection of personal data and the use of cookies.